Thats great
thank you all for your help
not so Grumpy
SOFAR ME3000SP
Re: SOFAR ME3000SP
Also have a watch of
to get an idea of why you need the settings.
to get an idea of why you need the settings.
Last edited by Tinbum on Mon Aug 12, 2024 5:19 pm, edited 2 times in total.
85no 58mm solar thermal tubes, 28.5Kw PV, 3x Sunny Island 5048, 2795 Ah (135kWh) (c20) Rolls batteries 48v, 8kWh Growatt storage, 22 x US3000C Pylontech, Sofar ME3000's, Brosley wood burner and 250lt DHW
Re: SOFAR ME3000SP
I really would strongly recomend that you get communication set up between the inverter and battery and then you wouldn't have these problems of incompatible settings.
85no 58mm solar thermal tubes, 28.5Kw PV, 3x Sunny Island 5048, 2795 Ah (135kWh) (c20) Rolls batteries 48v, 8kWh Growatt storage, 22 x US3000C Pylontech, Sofar ME3000's, Brosley wood burner and 250lt DHW
Re: SOFAR ME3000SP
Ok thanks for that
i will look at whats involved for communication to the sofar
i will look at whats involved for communication to the sofar
Re: SOFAR ME3000SP
I am a contributor to an open source project that enables CAN communication between a JK BMS and many inverter models.
You can find it here - https://github.com/Sleeper85/esphome-jk-bms-can
A solution like this will likely give much better control.
You can find it here - https://github.com/Sleeper85/esphome-jk-bms-can
A solution like this will likely give much better control.
10x 405W JA Solar panels (4.05kWp) @ 5 degrees
3x 405W Longi panels (1.22kWp) @ 90 degrees
16.5kWh DIY LifePo4 battery
Solis inverter/charger
0.6kW Ripple WT
64kWh Kia E-Niro
3x 405W Longi panels (1.22kWp) @ 90 degrees
16.5kWh DIY LifePo4 battery
Solis inverter/charger
0.6kW Ripple WT
64kWh Kia E-Niro
Re: SOFAR ME3000SP
Nice, I think the BMS can have CAN already on it if requested at the time of ordering. I bought a couple like that but haven't got round to fitting them yet so can't verify.MrPablo wrote: ↑Mon Aug 12, 2024 5:52 pm I am a contributor to an open source project that enables CAN communication between a JK BMS and many inverter models.
You can find it here - https://github.com/Sleeper85/esphome-jk-bms-can
A solution like this will likely give much better control.
85no 58mm solar thermal tubes, 28.5Kw PV, 3x Sunny Island 5048, 2795 Ah (135kWh) (c20) Rolls batteries 48v, 8kWh Growatt storage, 22 x US3000C Pylontech, Sofar ME3000's, Brosley wood burner and 250lt DHW
Re: SOFAR ME3000SP
great stuff
thanks for the info
will check this out
thanks for the info
will check this out
Re: SOFAR ME3000SP
I use the JK PB BMS with canbus, I connect directly to the master of two Sunny Islands and the Sunny Island takes its lead from the BMS. No alarms or warnings recorded in 120 days since first connection. Other than SOC drift there are no issues, did not even top balance the cells before connection to the BMS, let the JK 2A active balancer do it thing for 8 hours and it was balanced..
Re: SOFAR ME3000SP
Hi all
have been checking the inverters for a couple of weeks now since i changed the settings on the bms's
had no problems
charging is absolutely fine
learning a bit more as time goes by
thanks you all your help
great stuff
have been checking the inverters for a couple of weeks now since i changed the settings on the bms's
had no problems
charging is absolutely fine
learning a bit more as time goes by
thanks you all your help
great stuff
Re: SOFAR ME3000SP
85no 58mm solar thermal tubes, 28.5Kw PV, 3x Sunny Island 5048, 2795 Ah (135kWh) (c20) Rolls batteries 48v, 8kWh Growatt storage, 22 x US3000C Pylontech, Sofar ME3000's, Brosley wood burner and 250lt DHW