The Boy That Cried PV Extension

[Krill]

I've been wondering recently on the benefit, and frankly feasibility, of having the output from a DHW cylinder run through an electric boiler (I think nowty still has his cylinder plumbed to go through a gas boiler). The point being all the benefits of the normal cylinder and ToU tariffs with the potential to turbo boost the output if needed for flexibility.

This would mean a smaller EB but the running costs (as heating from a higher starting point) should be far smaller still, only use the EB when absolutely needed. With thermostatic mixers and running the DHW temp higher during higher use periods ie visitors even a 125l volume could be stretched quite far IMO.

The problems are one of space and wiring though, and additional costs, but it does provide the flexibility most people demand with a gas combi boiler

[Stinsy]

I've been wondering recently on the benefit, and frankly feasibility, of having the output from a DHW cylinder run through an electric boiler (I think nowty still has his cylinder plumbed to go through a gas boiler). The point being all the benefits of the normal cylinder and ToU tariffs with the potential to turbo boost the output if needed for flexibility.

This would mean a smaller EB but the running costs (as heating from a higher starting point) should be far smaller still, only use the EB when absolutely needed. With thermostatic mixers and running the DHW temp higher during higher use periods ie visitors even a 125l volume could be stretched quite far IMO.

The problems are one of space and wiring though, and additional costs, but it does provide the flexibility most people demand with a gas combi boiler

Even a 30kW gas combi is pretty slow to fill a bath. This is precisely why we have DHW tanks. A 3kW immersion can heat 250L of water from 10-60℃ in about 5hrs, this puts very little strain on your max demand and is perfectly reliable with zero maintenance for decades, and is economically viable on ToU. But is no good for “on demand”, you can’t expect the Mrs to wait 5hrs for a bath.

Electric boilers still require a DHW cylinder, but can reheat it much quicker because of their 10-14kW rating. On the other hand they’re very noisy, more complex and therefore likely to be unreliable, they cause big problems with max demand (particularly if you also charge an EV). You could therefore make use of a much smaller cylinder and rely on it being quick to reheat but you lose out on ToU.

[Mart]

Quick update on the upgraded system, and the unplanned decision to not use the GCH this year ..... well, hope to not use the GCH.

The recent cold spell, took Cardiff down to -1C for a day or two, plus a lovely snowstorm, but too brief to stay long.

I appreciate that -1C isn't impressive, but that's probably a fair figure for low winter temps here. The 'Cardiff bowl' is a temp control here, with rising hills/mountains on most sides inland, and the sea on the other. So the water temp tends to dampen temp extremes.

So, whilst we could well see -5C on occassions, and a week of cold may drain warmth from the house, I still think it was a decent test for average Dec-Feb conditions for the improvised leccy heating system. And it did fine. The two A2A units merrily pumped heat through the downstairs, and then some warming of the upstairs. I was running them a degree or two higher at night when going to bed, and opening the room doors wide to leak/spread heat as much as possible. During the day they run a bit lower (as rooms get too hot).

Batteries (20kWh) went down to 10-15% on the coldest day with next to zero PV, and down to about 20-25% on a sunnier day, with ~6kWh of gen. That 6kWh fig is interesting/important, as that's roughly what I expect in Dec, before gen rising in Jan. Dec forecast 175kWh, Jan 200kWh.

So looks like the basics might work. I have bought two oil rads, ....

[As posted earlier, I realised that a leccy boiler was resistive heating to the rads in the rooms, so why not cut out the middleman.]

.... just a very small in size 600W (£25), and a larger 2000W (800W/1,200W) with timer (£40). I had an idea of maybe getting 5 or 6 of the ickle ones, and they would pack away lovely in a tub, or on a shelf. But I may not need anymore, not sure. I'm only running the big one (at 800W), and an old 1,100W (400W/700W at 400W) through the night to warm two rooms that get a bit cold upstairs.

Problem areas as expected, and lots of questions:

1. Bathroom definitely cold, unless door left open for leaked heat to reach, but I'm thinking(?) this is easily solved with the planned leccy towel radiator. The room is tiny 1.8m by 2m, so I'm thinking of a towel rad immersion this is just an example. Has anyone used something like this, are they OK?

The wall the tall towel rad we have is on, is a lathe and plaster wall, and the rad lines up well with a socket on the other side. I'm thinking of maybe using a timer socket. Again, any thoughts? This seems simple and obvious, but I appreciate life is rarely that simple. I have a great plumber/builder friend, who actually installed our bathroom. He's who I'll be asking to do the work.


2. Next is the kitchen, here's some pics of the new heating system:






So, this is the A2A unit in the 'conservatory' (in reality a small room, just 2.4m cube), and it heats really easily as the unit is overpowered at 3.5kW, but that's to cope with heat (if we need A/C) and to ensure plenty of spare heat for its real purpose. The door leads to the main room/living room and with the conservatory at 23/24C the living room is about 20C with door to hallway wide open.

The kitchen is heated via blind optimism, and that small window from the conservatory. Surprisingly it's reaching around 17.5C on the opposite side of the kitchen, and outside wall. I'm pondering placing a fan on the windowsill, to see if it will pull the heat through better. I have tried a blow heater (with heat off), but it's very noisy, and doesn't excell at blowing. Heat will also enter the kitchen from the hallway where the heat from both A2A units travels, on its way up the stairs.

The original plan, was to put a simple hot air blower somewhere on a wall, but I'm pondering another of those towel rad heaters. Any reason why I can't put one in a 'normal' rad, as there's a lovely big double rad in place? So just some gentle heating through the night on cheap rate, and maybe timed to come on for evening cooking.


3. Not really a problem, but the spare room / gym / Cookie's room, is warming well with the 400W heater. It seems to modulate on and off roughly the same amount of time, so ~200W heating. So that's around 5kWh a day. May be better with door wide open (but Cookie foster cat is in there now), but I've mentioned a HW tank before, and that's where it will go ....... so, silly question, I'm expecting it to leak 1-2kWh of heat, which may top up the room, but could I deliberately set it for a higher temp in the winter, so it leaks a bit more. It would then effectively be a storage heater, leaking a bit of cheap rate leccy heat 24/7. Am I going mad? Two birds, one stone and all that. (In the 6/7 warmer months, we will have loads of PV, so it can heat a bit lower, as and when needed, from PV/batts.)


4. Lastly, not the end of the world if heating comes up short at times, as I can then just turn up the oil rads, turn on the blower etc. But I'm trying to aim for close to zero day-rate leccy consumption. Also, because my batts are DC side, then charging them winds my TGM backwards, and reduces FiT earnings. So all battery losses have a small cost. So another 2 birds / 1 stone, I've ordered a small portable battery system. Only 3kWh for £927. I hope to plug it in between the mains and one of the A2A units. Charge at night and power the unit during the day. That top up may be all I need taking me to 23kWh storage, or if it works well, I could get another for the other A2A unit.

I'm hoping during the summer, my friend who's getting my old PV panels, can use them (and the panels) to reduce their leccy bill, as they are struggling a bit.

So, anyone want to bet if I've found a good deal, or wasted the better part of a grand on some Chinese units ..... from a US based company ..... via a UK distributor ..... via Fed Ex delivery on Monday .... what can go wrong?

This is what I bought. have I made a mistake?

Apologies for the numerous spelling errors I'm sure I've made and missed.

[Countrypaul]

We have some bathroom towel immersion radiators controlled by similar to :
https://www.heatandplumb.com/acatalog/w ... gJ4avD_BwE

They were fitted a few years back but have no temperature control and unfortunately one overheated and had steam blasting out the top. I would definitely go with ones that ha a temperature limit (and looking at changing ours).

[Mart]

We have some bathroom towel immersion radiators controlled by similar to :
https://www.heatandplumb.com/acatalog/w ... gJ4avD_BwE

They were fitted a few years back but have no temperature control and unfortunately one overheated and had steam blasting out the top. I would definitely go with ones that ha a temperature limit (and looking at changing ours).

Thanks, do you have any suggestions, as this is totally new to me, and would rather not have steam related problems?