Sorry, can't give out his info to a newly joined member potentially stranded and looking for help. Sounds harsh I know but he's 80+ miles away and no guarantee to be paid for his time. My advice would be to try a Google search for motorhome sales places and go from there. Sorry, the guy I know does residential. I'm sure the board here will try and help.
Victron/Pylontech Installer in Scotland
Re: Victron/Pylontech Installer in Scotland
19.7kW PV SE, VI, HM, EN & DW
Ripple 7kW WT & Gen to date 19MWh
42kWh LFPO4 storage
95kWh Heater storage
12kWh 210ltr HWT.
73kWh HI5
Deep insulation, air leak ct'd home
Zoned GCH & Hive 2
WBSx2
Low energy bulbs
Veg patches & fruit trees
Ripple 7kW WT & Gen to date 19MWh
42kWh LFPO4 storage
95kWh Heater storage
12kWh 210ltr HWT.
73kWh HI5
Deep insulation, air leak ct'd home
Zoned GCH & Hive 2
WBSx2
Low energy bulbs
Veg patches & fruit trees
Re: Victron/Pylontech Installer in Scotland
Victron multiplus 12/500/20-16 Inverter - "Overload" notification and refuses to start- We spoke to our original supplier who got us to test various bits, all fine, but still not starting/working. Any help from the community greatly appreciated.
Re: Victron/Pylontech Installer in Scotland
why did it overload?
What was going on when it shut down
What firmware are you using/is it updated?
Bypass the MP. Reset the MP or at least power it off.
Switch it back on, then reconnect.
If that doesnt do it, then i have no clue.
If it does Update firmware.
Victron have a supurb helpline.
What was going on when it shut down
What firmware are you using/is it updated?
Bypass the MP. Reset the MP or at least power it off.
Switch it back on, then reconnect.
If that doesnt do it, then i have no clue.
If it does Update firmware.
Victron have a supurb helpline.
2.7kw Canadian solar. roof. 3kw solis G98 mcs
12kw midea ASHP
200l hot water
3152W RE, Whitelaw Brae
Octopus agile/outgoing fixed 15p
Planned;
Hybrid system
43kwh eve batteries, 3x16 280A
6-8+kw solar, DC connected.
12kw midea ASHP
200l hot water
3152W RE, Whitelaw Brae
Octopus agile/outgoing fixed 15p
Planned;
Hybrid system
43kwh eve batteries, 3x16 280A
6-8+kw solar, DC connected.
Re: Victron/Pylontech Installer in Scotland
I recall, I think it was Tinbum who had initial problems connecting up the newer pylontechs to a large inverter because of the large current inrush to charge up the capacitors in the inverter and the pylontechs shutdown with over current because the newer BMS is a bit more sensitive.
It might be as simple as that and the workaround is to use a resistor, long thin wire or similar to get over the initial current inrush.
It might be as simple as that and the workaround is to use a resistor, long thin wire or similar to get over the initial current inrush.
18.7kW PV > 109MWh generated
Ripple 6.6kW Wind + 4.5kW PV > 26MWh generated
5 Other RE Coop's
105kWh EV storage
60kWh Home battery storage
40kWh Thermal storage
GSHP + A2A HP's
Rain water use > 510 m3
Ripple 6.6kW Wind + 4.5kW PV > 26MWh generated
5 Other RE Coop's
105kWh EV storage
60kWh Home battery storage
40kWh Thermal storage
GSHP + A2A HP's
Rain water use > 510 m3
Re: Victron/Pylontech Installer in Scotland
Car light bulb is also good.nowty wrote: ↑Wed Apr 17, 2024 4:45 am I recall, I think it was Tinbum who had initial problems connecting up the newer pylontechs to a large inverter because of the large current inrush to charge up the capacitors in the inverter and the pylontechs shutdown with over current because the newer BMS is a bit more sensitive.
It might be as simple as that and the workaround is to use a resistor, long thin wire or similar to get over the initial current inrush.
85no 58mm solar thermal tubes, 28.5Kw PV, 3x Sunny Island 5048, 2795 Ah (135kWh) (c20) Rolls batteries 48v, 8kWh Growatt storage, 22 x US3000C Pylontech, Sofar ME3000's, Brosley wood burner and 250lt DHW
Re: Victron/Pylontech Installer in Scotland
Have you disconnected the load at the inverter and tried starting it like that? Just thinking worst case that could be a short somewhere that is giving the overload. I don't think the inrush current is relevant here as the overload warning is on the load (AC) side and not the DC.
Re: Victron/Pylontech Installer in Scotland
Thank you all for your helpful answers. We have tried everything, so looks like we need to return it to the supplier for further testing (or replacement).
Re: Victron/Pylontech Installer in Scotland
Have you tried posting a query on here?
16 x 230W Upsolar panels S Devon, 4kW Steca, 3.9 MWh FITs/yr
8 x 405W Longi panels, 250/60 MPPT, 3.3 MWh/yr
Victron MultiPlus II-GX 48/5000/70-50
10.65 kWh Pylontec Force-L2
zappi 7kW EVCS
Villavent whole-house MVHR
5000l rainwater system
Vaillant 12kW HP
8 x 405W Longi panels, 250/60 MPPT, 3.3 MWh/yr
Victron MultiPlus II-GX 48/5000/70-50
10.65 kWh Pylontec Force-L2
zappi 7kW EVCS
Villavent whole-house MVHR
5000l rainwater system
Vaillant 12kW HP
Re: Victron/Pylontech Installer in Scotland
Hi,
I am new to the forum and have been wanting to install a PV + battery system for my home and would like to fit a Victron system.
I contacted CCL Components Ltd. in Glasgow for information on Victron installers in N.E. Fife but haven't heard back from them and was wondering if any of you know anyone I can contact in my area ?
Many thanks in advance.
I am new to the forum and have been wanting to install a PV + battery system for my home and would like to fit a Victron system.
I contacted CCL Components Ltd. in Glasgow for information on Victron installers in N.E. Fife but haven't heard back from them and was wondering if any of you know anyone I can contact in my area ?
Many thanks in advance.
Re: Victron/Pylontech Installer in Scotland
RB Grant in St Andrews ?
Being doing solar for about 15 years now,
Not sure if they do victron stuff though,
Being doing solar for about 15 years now,
Not sure if they do victron stuff though,